
Quick Answer
Streaks and lines on laser printouts almost always trace back to one of five things: the toner cartridge, the drum (imaging unit), the corona wire or charge roller, the fuser, or, if the lines only show up on copies, a dirty scanner glass strip. The direction, color and spacing of the line tell you which part it is. Clean that part first, then replace it if the line comes back.
A line running down every page is one of the most common print problems in any office, and one of the most fixable. In many cases the cause is a consumable you can swap in a few minutes. In others, it’s a part that needs a technician. This guide shows you how to tell the difference before you spend money on the wrong fix.
Start Here: Is It the Printer or the Scanner?
If your machine copies as well as prints, run this 10-second test first:
- Print a document from your computer.
- Copy the same document using the document feeder on top of the machine.
Lines only on the copy? The printer is fine. The scanner is picking up a speck of dust, toner or correction fluid on the narrow glass strip the document feeder reads from, often on the left side of the glass. Turn the machine off, open the feeder lid, and wipe that strip and the matching white area on the underside of the lid with a soft cloth lightly dampened with water (spray the cloth, not the glass), then dry it. If the line stays after a thorough cleaning, the glass may be scratched and needs service.
Lines on both the print and the copy? The problem is inside the print engine. Keep reading.
What Your Streaks Are Telling You
Match what you see on the page to the most likely cause:
| What you see | Most likely cause | Try this first |
|---|---|---|
| Dark vertical line in the same spot on every page | Scratch or debris on the drum, a worn cleaning blade, or a dirty corona wire | Reseat the toner and drum; clean the corona wire if your model has one |
| Line only on copies, not on prints | Dirt on the scanner glass strip | Clean the feeder glass strip |
| White or light vertical streaks | Low or unevenly spread toner, debris blocking the laser or LED window, wrong paper setting | Rock the toner cartridge gently, clean the window, check the paper type |
| Horizontal lines or marks that repeat at the same interval | A rotating part (drum, roller, toner cartridge, fuser) | Measure the gap and match it to your model’s chart |
| Gray streaks or smears that rub off with a finger | Toner not fusing to the paper | Set the correct paper type; run a cleaning page |
| Streak in one color only (color laser) | That color’s toner, developer or drum | Replace the matching cartridge first |

Dark Vertical Lines or Streaks
A dark line that runs top to bottom in the same position on every page usually means something is marking the drum as it turns. HP lists the usual suspects as a scratched drum, a notch or foreign material on the cleaning blade, staples that went through the printer, and a cartridge near the end of its life. On color models, HP also notes the line can show up in a different color from the cartridge that’s actually causing it.
Two things to know before you buy parts:
- Many HP LaserJet cartridges include the drum. On those printers, a new toner cartridge replaces the drum too, so it’s the first thing to try.
- Brother and many other brands use a separate drum unit. If a new toner cartridge doesn’t fix the line, the drum is next. On Brother monochrome printers, cleaning the corona wire with the green tab on the drum unit often clears the line without replacing anything.
Lexmark’s own steps follow the same order: confirm you’re using a supported toner cartridge, remove and reinstall the imaging unit, then replace the imaging unit if the streak persists.
White or Light Vertical Streaks
A white or faded stripe means toner isn’t reaching that part of the page. The common causes are:
- Low or unevenly distributed toner. (Not sure how much is left? See how long toner lasts.) Take the cartridge out and gently rock it side to side to spread the toner, then reinstall it.
- Something blocking the light path. Brother recommends wiping the LED head windows with a dry, lint-free cloth and removing any torn paper, sticky notes or dust from inside the machine. Laser models have a similar window; check your manual for its location.
- A corona wire tab left out of position. On Brother drum units, if the green cleaning tab isn’t returned to its home position after cleaning, pages can come out with a vertical stripe.
- The wrong paper setting. Lexmark’s fix for white lines includes matching the paper type setting to the paper loaded. Make sure the paper type in the print dialog matches what’s in the tray.
Horizontal Lines and Repeating Marks
When a mark repeats down the page at a regular interval, a rotating part is leaving it once per revolution. The gap between marks matches that part’s circumference, which is how you identify it.
- Print a few pages of text or a print quality page.
- Measure the distance between two neighboring marks with a ruler.
- Compare it to the repeating-defect chart in your printer’s manual or support site.
The distances are model-specific, so always use your own printer’s chart. Two published examples:
- Brother HL-L3210CW / HL-L3230CDW / HL-L3270CDW: colored spots every 94 mm (3.7 in.) point to the drum unit; spots every 29 mm (1.1 in.) point to the toner cartridge.
- Lexmark MS521, MS621, B2650 and related models: defects repeating at 97 mm, 47 mm or 38 mm mean the imaging unit should be replaced.
HP publishes similar interval guides on the print quality troubleshooting pages for many LaserJet models.
Smears and Streaks That Rub Off
If the streak smudges when you run a finger over it, the toner isn’t being melted onto the paper. That points to the fuser or to a paper setting that’s telling the fuser to run too cool.
- Set the correct media type for the paper you’re using. Brother printers also offer an “Improve Toner Fixing” setting.
- Run the printer’s cleaning page if it has one. On the HP Color LaserJet Enterprise M551, for example, it’s under Device Maintenance > Calibration/Cleaning > Print Cleaning Page; other models use similar menus.
- If smearing continues on correctly set, dry paper, the fuser is likely wearing out. Replacing it is a technician job on most office printers, because the fuser runs extremely hot.
Color Laser Printers: One Color or All Colors?
On a color laser, the color of the streak narrows things down fast:
- Streak in one color: the problem is in that color’s supplies. Brother says to identify the color and replace that toner cartridge first, then the drum. Lexmark points to the developer unit for that color.
- Streaks across several colors: the problem is in a part all colors share, such as the transfer belt, the fuser or the imaging kit. Lexmark recommends replacing the imaging kit when streaks appear in multiple colors.
6 Safe Fixes to Try Before You Call a Technician
- Run the print-vs-copy test above to rule out the scanner.
- Print the printer’s built-in print quality or cleaning page. It shows the defect clearly and, on some models, cleans toner from the rollers.
- Remove the toner cartridge and rock it gently side to side, then reinstall it. Don’t touch the green or blue drum surface.
- Clean what the manufacturer lets you clean: the corona wire (slide the tab back and forth, then return it home), the LED or laser window with a dry lint-free cloth, and the scanner glass strip.
- Check your paper. Use dry paper from a freshly opened ream and make sure the paper type setting matches it.
- Swap in a known-good cartridge or drum if you have one. If the line disappears, you’ve found the part.
Safety first: Parts near the fuser are extremely hot right after printing, so let the printer cool before reaching inside. Brother warns never to use a vacuum cleaner on spilled toner, because the dust can ignite inside the vacuum, and never to use flammable sprays inside the machine. Wipe up loose toner with a dry, lint-free cloth instead.
When It’s Time to Call a Technician
Book a service call if:
- The line comes back after you’ve installed a new toner cartridge and a new drum.
- Toner smears or rubs off even with the correct paper setting (likely the fuser).
- Copies still show a line after you’ve cleaned the scanner glass (likely scratched glass or an optics issue).
- The printer shows an error code, or you hear grinding or clicking.
- Streaks appear in every color at once.
IOT Solutions has repaired laser printers and copiers for Twin Cities businesses since 1995. Our technicians come to your office and carry parts for most major brands, so most repairs are finished in one visit. Learn more about our laser printer repair service, or see our HP LaserJet repair page if you run HP printers. If the lines are on copies from a multifunction copier, our copier repair team can help.
A Note for Minnesota Offices: Watch the Humidity
Laser printers are sensitive to temperature and humidity. Brother lists low humidity or low temperature as a cause of ghosting, and high humidity or heat as a cause of white spots and toner scatter. HP lists low temperature and humidity among the causes of vertical lines on some color LaserJets. Dry, heated winter air and humid summers both show up on the page. Keep paper sealed in its ream until you need it, and keep printers away from heat vents and drafty exterior doors.
Related guides: laser printer printing blank pages and toner smearing and ghosting.
Frequently Asked Questions
Why does my laser printer print vertical lines?
Vertical lines usually come from the drum, the toner cartridge or the corona wire. Dark lines often mean a scratch or debris on the drum; light or white lines often mean low toner or something blocking the laser or LED window. If the lines only appear on copies, clean the scanner glass strip.
Why is there still a line after I replaced the toner cartridge?
If your printer uses a separate drum unit, the drum may be the cause. On Brother models, also check that the corona wire’s green tab is back in its home position. If a new toner cartridge and a new drum don’t fix it, the cause is likely the fuser, a roller or the optics, which needs a technician.
How do I fix horizontal lines on a laser printer?
Measure the distance between repeating lines and compare it to your printer’s repeating-defect chart. The distance identifies the roller or drum responsible. For example, on Brother’s HL-L3200 color series, marks every 94 mm point to the drum unit.
Can a cleaning page fix streaks?
Sometimes. A cleaning page can clear toner buildup from the fuser and rollers on printers that support it. It won’t fix a scratched drum, a worn fuser or a failing toner cartridge.
Is it worth repairing a laser printer that streaks?
Usually, if the cause is a consumable such as the toner cartridge or drum, because replacing it is the whole repair. If the fuser or laser unit has failed, compare the repair quote with the cost and age of the printer. Business-class printers are generally built to be serviced, so repair is often worthwhile.
Still seeing streaks? Call IOT Solutions at 651-448-2831 or request a service visit. We’ll diagnose the cause and give you a clear quote before any work begins.
Sources: HP Color LaserJet print quality troubleshooting (vertical lines); HP fuser cleaning page procedure; Brother print quality troubleshooting (HL-L3200 series); Lexmark solving printing problems; Lexmark troubleshooting vertical streaks.
